Tool to set hood bumper rivets. Works better with outside lip grounded off. For 1930 1931 1932 1933 1934 Chrysler Cars

Screw nail. For All Chrysler Cars

Bolts, nuts and washers for Hood latches, hood bumpers and motor mount covers to frame, CG (1931 Imperial 8). (16 pieces). For 1931 Chrysler Cars

Hex nut fastener for hood and latch, Stainless. For 1931 Chrysler Cars

Lock washer for hood and latch, Stainless. For 1931 Chrysler Cars

Stainless square and hex nuts and lock washers (32 pieces), CG (1931 Imperial 8). For 1931 Chrysler Cars

Hood Center End Cap, With retainer, screws and nuts. Does one end. Car uses two. For 1931 1932 Chrysler Cars

Hood Bumper for Hood side panel. Metal core as original, six per car. Imperial 80, CG (1931 Imperial 8), CH (1932 Imperial 8), CQ (1933 Imperial 8) and Chrysler 66, 70, 75, 77... For 1930 1931 1932 1933 Chrysler Cars

Hood Bumper. Fender to hood. Two per car. Held by four rivets. For 1931 1932 1933 Chrysler Cars

Hood Brackets, Rattle brackets for bottom rubber bumpers. Set of 4. CG (1931 Imperial 8). Also use rubber pads #31C010349. For 1931 1932 Chrysler Cars

Hood latch swivel and hood bumper rubber pads with rivets. Set of four rubber pads in brass, chrome plated cups. Imperials and other large Chryslers. Takes 2 sets per car. To ... For 1930 1931 Chrysler Cars

Base bracket for 31C010351. For 1931 Chrysler Cars

Swivel, hood latch. Exact copy, not plated, use with part #31C010349. For 1930 1931 Chrysler Cars

For radiator to cowl. 1 only (rod w/ kink). For 1931 1932 Chrysler Cars

Radiator support rod clamp. Top and bottom (2 pieces). For 1931 Chrysler Cars

Split rivets for webbing. Used for cowl and grille shell to hood, CG (1931 Imperial 8). For 1931 Chrysler Cars

Hood center end cap retainer. For 1931 1932 Chrysler Cars

Hood vent door pads. Replaces #364330. Self retaining. Set of 20 needed per car. Imperials with doors on hood, Cl, CO, CQ (1933 Imperial 8) and CT. For 1933 Chrysler Cars

Hood Corners. Fits flat corners. 80 angle, 1/4" to 3/8" corner radius. 1-3/8" wide. For 1930 1931 1932 1933 Chrysler Cars

Flange needs to be removed. CG (1931 Imperial 8) Phaeton and Roadsters, 1931 and ?. For 1931 Chrysler Cars

Hood pad corners. Replaces #97224. 90 degree angle. (2 per car). For 1930 1931 1932 1933 1934 Chrysler Cars

Hood panel center bracket pad. Hollow, to fit over original steel bracket. Many models. For 1933 Chrysler Cars

Pads, hood rear corners. Open angle for long hood. Metal core as original. Chrysler Imperial. For 1932 Chrysler Cars

Hood corners, steel core pad. Approximately 80 degree angle. Integral tabs for installing. Many WPC Models. Replaces #466130 and #450597. Many models -front, used on my CG (19... For 1933 1934 Chrysler Cars

Pads, hood front corners. Rubber with metal core as original. Chrysler Imperial. For 1932 Chrysler Cars

Hood latch swivel and hood bumper rubber pads with rivets. Set of four rubber pads. Use with parts #31C010351 and 31C150301. For 1931 Chrysler Cars

Hollow rivets for hold down and lower hood latch bumpers, CG (1931 Imperial 8). For 1931 Chrysler Cars

Webbing with rivets for grille shell to hood, CG (1931 Imperial 8). For 1931 1932 1933 Chrysler Cars

Webbing with nails for cowl, CG (1931 Imperial 8). For 1931 1932 1933 Chrysler Cars

Anti-squeak webbing. DOES NOT have hollow center. Fasten with rivets if so found originally. Excellent quality. For 1931 1932 1933 1934 Chrysler Cars